5-Volt Power Supply

Product Code: OTC2506

Product NO:NW-10
Input Voltage: 90-264VAC
Output Voltage: 12,15,24
Output Power: 10W
Size: 77*48*20mm

৳ 1,000


5-Volt Power Supply Specs:

  • International broad voltage AC input
  • Protection: short-circuit, overload, overheat
  • 100% full-load aged
  • 300VAC surge for 5 seconds withstandable
  • Working temperature up to 60℃
  • 5G vibration tested
  • High efficiency and long life span
  • 2 years warranty
Product No. NW-10-5L NW-10-12L NW-10-15L NW-10-24L
Output DC voltage 5V 12V 15V 24V
Rated Current 2A 0.8A 0.6A 0.4A
Current Range 0-2A 0-0.8A 0-0.6A 0-0.4A
Rated Power 10W 10W 10W 10W
Ripple and Noise(Max)Note.2 100mVp-p 150mVp-p 180mVp-p 240mVp-p
Voltage adjustment 4.8-5.4V 10.8-13.2V 13.5-16.5V 22-27.6V
Voltage Accuracy  Note3 ±2% ±1% ±1% ±1%
Linear Adjustment Note4 ±0.5% ±0.5% ±0.5% ±0.5%
Load Adjustment  Note5 0.015 ±0.5% ±0.5% ±0.5%
Start and rise time 1000ms,30ms/230VAC 1000ms,30ms/110V
Hold timeTyp 50ms/230VAC  10ms/115AC
Input Voltage range 90-264VAC/120-370VDC
Frequency range 47-63HZ
EfficiencyTyp 75% 80% 81% 82%
AC current Typ 0.35A/90V  0.2A/220V
Surge current (Typ) Cold Start65A/230VAC
Current leak <2mA/240VAC
Protection Overload Larger than 105% of capacity
restoration after abnormity removed
Overheat Overheat protection starts when the temperature in the transistor over 140
Automatic restoration when the temperature is back to normal
Environment Working temp. -20+60(Refer to the attenuation curve)
Working humidity 2090% RH, without condense
Storage temp & humidity -40+80
Temp. coefficient ±0.03%/ 050℃)
Vibration-proof 10500HZ,5G 10min / cycleXYZ axes 60 min each
Safety reg. & EMC    (Note.6 Safety regulation GB195110.1-2004/IEC61347-1:2003  CE(EMC+LVD)
Voltage proof I/P-O/P:1.5KVAC
insulation resistance I/P-O/P:100M Ohms/500VDC/25/70% RH
EMC irradiation EN 55015:2006;EN61000-3-2:1995+A2:2005
EMC disturbance proof EN 61000-3-2:2006;
Dimensions 77*48*20mm(L*W*H)
Packing 0.08kg/PCS;200PCS/19.5kg
Notes: 1. Unless specially indicated, all data are taken under 230VAC input, rated load, and 25 environment temp.
2.Ripple and noise: measured with a 12” double ripple cord connected in parallel with a 0.1μF and a 47 μF capacitor on 20MHz bandwidth.
3.Accuracy: including preset errors, linear adjustment rate, and load adjustment rate.
4.Linear adjustment: taken under-rated load from low voltage to high voltage.
5.Load adjustment: taken under 0~100% of rated load.
6. Power supply is taken as part of the whole system and needs to be confirmed with terminal instruments for EMC.

# Check Access Control Products


There are no reviews yet.

Be the first to review “5-Volt Power Supply”

Your email address will not be published. Required fields are marked *