Cart

Your Cart is Empty

Back To Shop

75-Volt 6-Amp Power Supply

SKU:

3,050৳ 

  • Product NO:NW-75
  • Input Voltage:90-264VAC
  • Output Voltage:12,15,24,48
  • Output Power:75W
  • Size:160*98*38mm

75-Volt 6-Amp Power Supply Specs:

  • International broad voltage AC input
  • Protection: short-circuit, overload, overheat
  • 100% full-load aged
  • 300VAC surge for 5 seconds withstandable
  • Working temperature up to 60℃
  • 5G vibration tested
  • High efficiency and long life span
  • 2 years warranty
Specifications
Product No. NW-75-12 NW-75-15 NW-75-24 NW-75-48
Output DC voltage 12V 15V 24V 48V
Rated Current 6A 5A 3A 1.5A
Current Range 0-6A 0-5A 0-3A 0-1.5A
Rated Power 75W 75W 75W 75W
Ripple and Noise(Max)Note.2 150mVp-p 180mVp-p 240mVp-p 250mVp-p
Voltage adjustment 10.8-13.2V 13.5-16.5V 22-27.6V 44-52V
Voltage Accuracy  Note3 ±1% ±1% ±1% ±1%
Linear Adjustment Note4 ±0.5% ±0.5% ±0.5% ±0.5%
Load Adjustment  Note5 ±0.5% ±0.5% ±0.5% ±0.5%
Start and rise time 1000ms,30ms/230VAC 1000ms,30ms/110V
Hold timeTyp 50ms/230VAC  10ms/115AC
Input Voltage range 90-264VAC/120-370VDC
Frequency range 47-63HZ
EfficiencyTyp 80% 81% 82% 82%
AC current Typ 1.38A/90V  0.56A/220V
Surge current (Typ) Cold Start65A/230VAC
Current leak <2mA/240VAC
Protection Overload Larger than 105% of capacity
restoration after abnormity removed
Overvoltage
Overheat
Environment Working temp. -20+60(Refer to the attenuation curve)
Working humidity 2090% RH, without condense
Storage temp & humidity -40+80
Temp. coefficient ±0.03%/ 050℃)
Vibration-proof 10500HZ,5G 10min / cycleXYZ axes 60 min each
Safety reg. & EMC    (Note.6 Safety regulation GB195110.1-2004/IEC61347-1:2003  CE(EMC+LVD)
Voltage proof I/P-O/P:1.5KVAC
insulation resistance I/P-O/P:100M Ohms/500VDC/25/70% RH
EMC irradiation EN 55015:2006;EN61000-3-2:1995+A2:2005
EMC disturbance proof EN 61000-3-2:2006;
Dimensions 160*98*38mm(L*W*H)
Packing 0.34kg/PCS;36PCS/12.8kg
Notes: 1. Unless specially indicated, all data are taken under 230VAC input, rated load, and 25 environment temp.
2.Ripple and noise: measured with a 12” double ripple cord connected in parallel with a 0.1μF and a 47 μF capacitor on 20MHz bandwidth.
3.Accuracy: including preset errors, linear adjustment rate, and load adjustment rate.
4.Linear adjustment: taken an under-rated load from low voltage to high voltage.
5.Load adjustment: taken under 0~100% of rated load.
6. Power supply is taken as part of the whole system and needs to be confirmed with terminal instruments for EMC.

# Check Access Control Products

Reviews

There are no reviews yet.

Be the first to review “75-Volt 6-Amp Power Supply”

Your email address will not be published. Required fields are marked *

Cart

Your Cart is Empty

Back To Shop