BOSCH LBB1938 Power Amplifier
SKU:133,000৳
The Bosch LBB 1938/20 is a powerful 480 W power amplifier in a 3U high 19”case for rack mounting or tabletop use.
LEDs on the front panel of the LBB1938/20 show the status of the amplifier: power, audio output level, and supervised functions.
This high performance unit fulfills a wide range of public address requirements at a surprisingly low cost.
There are two separate priority controlled 100 V outputs for zones that only need announcements made via the priority input, and for zones that will not get any announcements made via the priority input.
Rack mounting brackets supplied.
- 480 watts
- Very high audio performance power amp
- Can be used to boost Plena Voice alarm systems with system monitoring
- XLR and jack input with XLR and Jack loop through outputs
- 100 volt line input. Ideal for remote location booster amps
- 100v, 70v and 8 ohm outputs
- 24v override relay output
- Temperature controlled fan
- AC and 24VDC operation
- LED VU Meter
- Dual inputs with priority switching
- Temperature controlled forced front to back
- Mains, battery back-up, and pilot tone supervision
- TÜV certified according to IEC 60849
BOSCH LBB1938 Power Amplifier Spces:
- Voltage: 230VAC, ±10%, 50/60 Hz
- Inrush current :19 A
- Max power consumption: 2200 VA
- Battery power supply
- Voltage: 24 VDC, +20% / -10%
- Current max: 30 A
Performance
- Output power (rms/maximum): 480 W / 720 W
- Power reduction on backup power: -1 dB
- Mains power supply
- Frequency response: 50 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output)
- Distortion: <1% @ rated output power, 1 kHz
- S/N (flat at max volume): >90 dB
- Line inputs: 2 x
- Connector: 3-pin XLR, balanced
- Sensitivity: 1 V
- Impedance: 20 kohm
- CMRR: >25 dB (50 Hz to 20 kHz)
- Gain: 40 dB
- 100 V input: Connector Screw, unbalanced
- Sensitivity: 100 V
- Impedance: 330 kohm
- Line loop-through output 2 x
- Connector: 3-pin XLR
- Nominal level: 1 V
- Impedance: Direct connection to line input
- Loudspeaker outputs: 3 x
- Connector: Screw, floating
- Direct output: 100 V, 70 V, 8 ohm
- Priority only (from input 1): 100V or 70 V internally selectable
- Music (non-priority) only: 100V or 70 V internally selectable
Power consumption
Max power: 990 W
-3dB 715 W
-6dB 510 W
Pilot tone* 110 W
Idle 25 W
24 VDC operation
Max power 32 A (770 W)
-3 dB: 26 A (625 W)
-6 dB: 18 A (430 W)
Pilot tone*: 3.8 A (91 W)
Idle: 0.7 A (17 W)
* 20 kHz -20dB with maximum loudspeaker load
Mechanical
Dimensions (H x W x D): 145 x 430 x 370 mm / (19″ wide, 3U high, with feet)
Weight: Approx. 25 kg
Mounting: Standalone, 19”rack
Color: Charcoal
| Brand |
|---|
Related products
-
Bosch PRS-1P500 Power Amplifier
195,000৳Add to cartThere are four types of Power Amplifier units in the Praesideo product range. These differ in the number of amplifier channels per frame: one, two, four, or eight. The overall power rating is 500 watts for all of the amplifiers. The Power Amplifiers can be set to 100 V, 70 V, and 50 V output tappings. They have short-to-ground and short-circuit detection functions, and can generate their own pilot tone for supervision purposes
-
BOSCH PLE2CS Plena Call Station
35,700৳Add to cartThe Bosch Plena PLE-2CS 2 zone paging microphone is a high-quality call station with a sturdy metal base designed for use with the PLE series of amplifiers such as the Bosch PLE-2MA120 and PLE-2MA240. In addition to tabletop use, the special design of the PLE2CS enables the unit to be neatly flush-mounted. 2 zone selection keys enable either or both zones to be selected for paging – indicated by LEDs.
- Modern two-zone call station for the PLE series
- Selectable gain
- Speech filter and limiter
- Output level control
- Loop-through option for up to 8 call stations
- LED indications for zone selection, busy, and power on
-
Bosch Dicentis DCNM-HDMIC
Read moreThe Bosch DCNM-HDMIC is a discreet plug-in microphone for the Bosch Dicentis wireless discussion devices – DCNM-WD and DCNM-WDE.
The unobtrusive design enables a clear and unobstructed view of the meeting room and two precisely positioned capsules give a high-directive response, ideal for noisy conditions.
The DCNMHDMIC has low susceptibility to interference from mobile phones and red or green illuminators indicate whether the microphone is active (red) or whether the request-to-speak is accepted.
- Discrete microphone for user convenience
- High directive response
- Low susceptible for mobile phones Ultra low noise
- Freedom of movement
Call for Price
-
Bosch PRS-CSI Call Station Interface
70,000৳Add to cartProduct Code: OTC2472
The PRS-CSI is an interface between a single remote call station, PRS-CSR, or a remote call station kit, PRS-CSRK, and the fiber optical Praesideo network. It uses CAT-5 cable for the connection to the remote call station. The CAT-5 cable, carrying digital audio and control data, can be as long as 1 km.
The length of the CAT-5 cable is not a part of the Praesideo optical network length. This considerably increases the overall possible length of the optical network, especially in cases, where the call station is located far from the rest of the system.
The call station interface can get its power from the Praesideo network, and/or from a local power supply. It is fully supervised.
Reviews
There are no reviews yet.