BOSCH LBB1938 Power Amplifier
SKU:133,000৳
The Bosch LBB 1938/20 is a powerful 480 W power amplifier in a 3U high 19”case for rack mounting or tabletop use.
LEDs on the front panel of the LBB1938/20 show the status of the amplifier: power, audio output level, and supervised functions.
This high performance unit fulfills a wide range of public address requirements at a surprisingly low cost.
There are two separate priority controlled 100 V outputs for zones that only need announcements made via the priority input, and for zones that will not get any announcements made via the priority input.
Rack mounting brackets supplied.
- 480 watts
- Very high audio performance power amp
- Can be used to boost Plena Voice alarm systems with system monitoring
- XLR and jack input with XLR and Jack loop through outputs
- 100 volt line input. Ideal for remote location booster amps
- 100v, 70v and 8 ohm outputs
- 24v override relay output
- Temperature controlled fan
- AC and 24VDC operation
- LED VU Meter
- Dual inputs with priority switching
- Temperature controlled forced front to back
- Mains, battery back-up, and pilot tone supervision
- TÜV certified according to IEC 60849
BOSCH LBB1938 Power Amplifier Spces:
- Voltage: 230VAC, ±10%, 50/60 Hz
- Inrush current :19 A
- Max power consumption: 2200 VA
- Battery power supply
- Voltage: 24 VDC, +20% / -10%
- Current max: 30 A
Performance
- Output power (rms/maximum): 480 W / 720 W
- Power reduction on backup power: -1 dB
- Mains power supply
- Frequency response: 50 Hz to 20 kHz (+1/‑3 dB @ ‑10 dB ref. rated output)
- Distortion: <1% @ rated output power, 1 kHz
- S/N (flat at max volume): >90 dB
- Line inputs: 2 x
- Connector: 3-pin XLR, balanced
- Sensitivity: 1 V
- Impedance: 20 kohm
- CMRR: >25 dB (50 Hz to 20 kHz)
- Gain: 40 dB
- 100 V input: Connector Screw, unbalanced
- Sensitivity: 100 V
- Impedance: 330 kohm
- Line loop-through output 2 x
- Connector: 3-pin XLR
- Nominal level: 1 V
- Impedance: Direct connection to line input
- Loudspeaker outputs: 3 x
- Connector: Screw, floating
- Direct output: 100 V, 70 V, 8 ohm
- Priority only (from input 1): 100V or 70 V internally selectable
- Music (non-priority) only: 100V or 70 V internally selectable
Power consumption
Max power: 990 W
-3dB 715 W
-6dB 510 W
Pilot tone* 110 W
Idle 25 W
24 VDC operation
Max power 32 A (770 W)
-3 dB: 26 A (625 W)
-6 dB: 18 A (430 W)
Pilot tone*: 3.8 A (91 W)
Idle: 0.7 A (17 W)
* 20 kHz -20dB with maximum loudspeaker load
Mechanical
Dimensions (H x W x D): 145 x 430 x 370 mm / (19″ wide, 3U high, with feet)
Weight: Approx. 25 kg
Mounting: Standalone, 19”rack
Color: Charcoal
| Brand |
|---|
Related products
-
BOSCH PLN‑6TMW Plena Weekly Timer
126,600৳Add to cartThe Plena Weekly Timer is an accurate timer for use in public address systems. It is ideally suited for schools, shopping malls, and all other venues that need regularly timed messages, signals, or other controls. It is ideally suited for connection to the Plena Message Manager and Voice Alarm System.
-
Bosch PRS-CSR Call Station Remote
65,500৳Add to cartThe PRS-CSR is a call station with the same functionality as the basic call station, LBB 4430/00, but it uses CAT-5 cable for its connection to the Praesideo network. It connects, one-to-one, to the call station interface, PRS-CSI, which is part of the Praesideo optical network.
The CAT-5 cable, carrying digital audio and control data, can be as long as 1 km. The length of the CAT-5 cable is not a part of the Praesideo optical network length. This considerably increases the overall possible length of the optical network.
The PRS-CSR can be extended with up to 16 keypads (LBB 4432/00 or LBB 4434/00), each with eight programmable keys. Extension with a numeric keypad (PRS-CSNKP) is also possible.
-
BOSCH PLE2CS Plena Call Station
35,700৳Add to cartThe Bosch Plena PLE-2CS 2 zone paging microphone is a high-quality call station with a sturdy metal base designed for use with the PLE series of amplifiers such as the Bosch PLE-2MA120 and PLE-2MA240. In addition to tabletop use, the special design of the PLE2CS enables the unit to be neatly flush-mounted. 2 zone selection keys enable either or both zones to be selected for paging – indicated by LEDs.
- Modern two-zone call station for the PLE series
- Selectable gain
- Speech filter and limiter
- Output level control
- Loop-through option for up to 8 call stations
- LED indications for zone selection, busy, and power on
-
Bosch PRS-CSI Call Station Interface
70,000৳Add to cartProduct Code: OTC2472
The PRS-CSI is an interface between a single remote call station, PRS-CSR, or a remote call station kit, PRS-CSRK, and the fiber optical Praesideo network. It uses CAT-5 cable for the connection to the remote call station. The CAT-5 cable, carrying digital audio and control data, can be as long as 1 km.
The length of the CAT-5 cable is not a part of the Praesideo optical network length. This considerably increases the overall possible length of the optical network, especially in cases, where the call station is located far from the rest of the system.
The call station interface can get its power from the Praesideo network, and/or from a local power supply. It is fully supervised.
Reviews
There are no reviews yet.